Additional Information About A & I COATINGS E4112 EPOXY RESIN
A & I Coatings ENVIROSET 4112 is a two-pack pigmented, solvent free, 100% solids epoxy with excellent surface hardness and adhesion. It exhibits high water resistance, chemical and oil resistance with the ability to build virtually unlimited film thickness.
ADVANTAGES OF E4112 EPOXY COATING
Excellent for protecting old and new concrete surfaces
Low VOC
Excellent chemical and mechanical resistance
Excellent hot tyre pick-up resistance
Excellent wear and abrasion resistance.
Excellent fuel and chemical resistance.
Produces smooth and glossy finish, slip resistance floor finishes can be achieved by adding anti-slip media to the coating system.
Available in a wide range of colours to achieve an attractive & aesthetically pleasing finish.
RECOMMENDED PREPARATION METHOD PRIOR TO APPLYING REAL EPOXIES
Recommended diamond tooling grits to prepare the floor prior to applying A&I Coatings E4112
Diamond grinding is recommended method of preparing new & old substrates prior to applying A&I Coatings E4112
The purpose behind concrete grinding is to remove any flaking paint and other types of contamination to achieve a clean surface as well as remove any sealer or curing agent and open concrete pores allowing 1st coat of A& I Coatings E4112 to penetrate deep into the surface and seal the floor.
Acid Etching might be used as an alternative option to prepare the floor for more information on how to acid etch your floor click here to be directed to an external blog. Hydrochloric acid can be purchased from Bunnings, pool shops and local hardware stores
Preparation is the key to achieving a long-lasting floor-coating system
PCD plugs to remove flaking paint and then use grinding shoes to smooth out the floor before applying the coating.
Guide to How much product you will need to cover your space using A & I Coatings E4112
Consumption will depend on the following factors:
Surface porosity | to acheive best results, old and soft concrete may require an additional coat of epoxy
Application method | Squeege application method will use more product but will provide better finish, alos size of the roller nap and amount of product applied to the floor can play a big roller in consumption rate.
Consumption Coverage Guide | 20L pigmented E4112 Epoxy Flooring kit applied using a 11 – 12mm nap roller
Area Size
1st coat
2nd Coat
Recommended Minimum no of coats
Required no of kits
Up to 50m2
10 liters
10 liters
Two coats
One Kit
Up to 100m2
20 Liters
20 Liters
Two Coats
Two Kits
Up to 150m2
30 Liters
30 liters
Two Coats
Three Kits
Anti-Slip Media for Epoxy flooring to meet Australian Safety Standards
The anti-slip media supplied with this pack will not pass slip rating testing, if your project requires a specific slip rating, use the chart below as a guide to achieve R or P rated slide resistance floor covering using alternative grit anti-slip media. Information below should only be used as a guide and applicator must ensure the end product meets the required slip rating.
Slip Rating
P3 or R10
P4 or R11
P5 or R12
Recommended Product
Boral 30/60 sand 80 grit Aluminum Oxide
Boral 1mm sand 46 or 30 grit Aluminum Oxide
Boral 1mm sand 24 grit Aluminum Oxide
Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.
Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.
Excellent service and advice from Alex, I highly recommend these guys for anyone who is looking to purchase high quality epoxy flooring products and hiring a concrete grinder
Sean attended a job that we were doing to not only deliver product purchased but also to spend time with my staff to ensure that they were familar with the new product that we were using. I found Sean to be diligent in every aspect. He also gave advise on different procedures new to us. I could not recomend him and his team highly enough.
Unfortunately I don’t remember the name of the staff member that helped but he went to great lengths to help ensure I got the right product for the job I needed. What’s better was the product recommended was excellent and worked perfectly.
Extremely wonderful staff, leva was incredibly insightful. The Epoxy flooring on my garage floor looks amazing. I will definitely be returning to purchase more epoxy products for my next project
Ray Nadar –
great coverage and it was easy to apply!