Australia Wide Shipping

11

Sikadur 42HF – 18kg kit

$355.00 inc GST

Very High Flow, Cost Effective Epoxy Resin Grout

 

Quantity:
SKU: AEF59F Categories: ,

Sikadur®-42 HF is a pourable, multi-functional high density epoxy grout based on a 2-component solvent free epoxy resin system containing fine fillers. Sikadur-42 HF exhibits excellent flow characteristics in general grouting applications.

Reviews

There are no reviews yet.

Be the first to review “Sikadur 42HF – 18kg kit”

Your email address will not be published. Required fields are marked *

USES

As a grout for manufacturing plants and civil engineering application:

  • Crane rails
  • Machine bedding and baseplates
  • Holding down bolts
  • Stanchions
  • Starter bars
  • Cavity filling
  • Bridge bearings

 

CHARACERISTICS AND ADVANTAGES

  • Cost effective epoxy grout
  • Applicable at low temperatures.
  • High mechanical strengths.
  • High flow characteristics
  • Supplied in factory proportioned units.
  • Shrink free.
  • Can be bulked out with aggregate of thicker pour applications
  • Excellent chemical resistance to water, sea water, waste water, sewage, fuels, oils, dilute acids and dilute alkalis.

Mixed: Grey

18 kg net pre-proportioned kit

SUBSTRATE QUALITY

Mortar and concrete must be older than 28 days (dependent on minimum strength requirements). Verify the substrate strength (concrete, natural stone etc.).

The substrate surface (all types) must be clean, dry and free from contaminants such as dirt, oil, grease,
existing surface treatments and coatings etc. Steel substrates must be de-rusted to a standard equivalent to Sa 2.5.
The substrate must be sound and all loose particles must be removed. Substrate must be dry or mat damp and free from any standing water, ice etc.

SUBSTRATE PREPARATION

Surface and base plate contact area must be clean and sound. For best results, the substrate should be dry. Remove dust, laitance, oils, grease, curing compounds, impregnations, waxes, foreign particles, coatings, and disintegrated materials by mechanical means, i.e. chipping
with a chisel, blastcleaning etc. All anchor pockets or sleeves must be free of water. Blastcleaning metal base plates to an acceptable quality standard equivalent to SA 2.5 for maximum adhesion. Apply grout immediately to prevent re-oxidizing.

Forming:
The consistency of the Sikadur®-42 HF epoxy grout system requires the use of permanent or temporary forms to contain the material around base plates, for example. In order to prevent leakage or seepage, all of these formers must be sealed. Apply polyethylene film or wax to all forms to prevent adhesion of the grout. Prepare the formwork to maintain more than 100 mm liquid head to facilitate placement. A grout box
equipped with an inclined trough attached to the form will enhance the grout flow and minimize air encapsulation.

MIXING

Prior to mixing the components should be stored at 15-20°C for the previous 24 hours. Mix all of component A (Grey Resin) with all of component B (Hardener) using a slow speed drill (maximum 600 rpm) and windmill stirrer. Mix until a homogeneous and streak free mixture results.

Part A SDS | Part B SDS | PDS

https://aus.sika.com/en/construction/grouts-landscapinganchoring/epoxy-grouts/sikadur-42-hf.html

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.

Google Rating
5.0
Based on 79 reviews
×
js_loader