Australia Wide Shipping

Screenshot 2023-01-04 213749Screenshot 2023-01-04 213749

Sika MonoTop 723N – 20kg

$59.00 inc GST

R3 Pore Sealer and Levelling Mortar

Quantity:
SKU: FF952D Categories: ,

Sika MonoTop®-723 N is a polymer modified surfacing/finishing mortar, ready to mix, meeting the requirement of class R3 of EN 1504-3.

Reviews

There are no reviews yet.

Be the first to review “Sika MonoTop 723N – 20kg”

Your email address will not be published. Required fields are marked *

USES

  • Thin layer render
  • Use as a concrete pore sealer / levelling mortar
  • Repairing of minor defects (pores and honeycombed concrete)
  • Suitable for restoration work (Principle 3, method 3.1 and 3.3 of EN 1504-9)
  • Suitable for preserving or restoring passivity (principle 7, method 7.1 and 7.2 of EN 1504-9)

 

CHARACTERISTICS AND ADVANTAGES

  • Easy to apply and excellent finishing
  • Suitable for hand or wet spray application
  • Can be applied up to 5 mm thick per application layer
  • Class R3 of EN 1504-3
  • Restoration work
  • Sulphate resistant
  • Low cracking sensitivity
  • Very good resistance to water and chloride penetration
  • Compatible with Sikagard® overcoat systems
  • A1 fire rating

Grey powder

20 kg bag

MIXING

Sika MonoTop®-723 N can be mixed with a low speed (<500 rpm) hand drill mixer or for machine application, using a force action mixer 2 to 3 bags or more at once depending the type and size of mixer. In small quantity, Sika MonoTop®-723 N can also be manually mixed.
Pour the recommended water in a suitable mixing container. While stirring slowly, add the powder to the water and mix thoroughly at least for 3 minutes to the required consistency.

APPLICATION

Sika MonoTop®-723 N can be applied either manually using traditional techniques or mechanically using wet spray equipment. Thoroughly pre-wet the prepared substrate a recommended 2 hours before application. Keep the surface wet and do not allow to dry. Before application remove excess water e.g. with a clean sponge. The surface shall appear a dark matt appearance without glistening and surface pores and pits shall not contain water.

When manually applying the mortar first make a scratch coat by firmly scrapping the repair mortar over the substrate surface to form a thin layer and fill any pores or pits in the surface. The surface can be finished according to the requirements using a float or with a relevant wooden or plastic float or damp sponge.

 

CURING TREATMENT

Protect the fresh mortar immediately from premature drying using an appropriate curing method e.g. moist geotextile membrane, polythene sheet etc.

Safety Data Sheet (SDS)_GHS7Safety Data Sheet (SDS) | Product Data Sheet (PDS)

https://aus.sika.com/en/construction/concrete-repair-protection/concrete-repair-mortars/cementitious-repairmortars/sika-monotop-723n.html

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.

Google Rating
5.0
Based on 79 reviews
×
js_loader