Australia Wide Shipping

Screenshot 2023-01-04 221012Screenshot 2023-01-04 221012

SikaGrout GP – 20kg

$18.00 inc GST

GENERAL PURPOSE, “CLASS A” PUMPABLE, SHRINKAGE-COMPENSATED CEMENTITIOUS GROUT

Quantity:
SKU: BE783B Categories: ,

SikaGrout® GP AU is a pumpable, shrinkage-compensated, flowable cementitious “Class A” grout with extended working time to suit local ambient temperatures.

Reviews

There are no reviews yet.

Be the first to review “SikaGrout GP – 20kg”

Your email address will not be published. Required fields are marked *

USES

SikaGrout® GP AU is a general purpose grout suitable for the following applications:

  • General purpose grouting
  • Grouting works for machine foundations, anchor bolts etc.
  • Precast grouting
  • Filling of cavities, gaps, recesses, etc.

For precision grouting, SikaGrout®-212HP is recommended.

 

CHARACTERISTICS AND ADVANTAGES

▪ Easy to mix and apply
▪ Flowable consistency (according to mix)
▪ Rapid strength development
▪ Non-corrosive
▪ Non-toxic
▪ Iron and chloride free
▪ Shrinkage-compensated
▪ Good pumping properties

Grey premixed powder

20 kg bags

MIXING

Place about 70–80 % of the premeasured clean water (depending on consistency required – refer to “Mix Ratio”) into a clean container and gradually add the whole bag of SikaGrout® GP AU into it while continuously mixing. Add the remaining water until the desired consistency is obtained. Mix for 3–5 minutes with a low speed drill (500 rpm max.).

APPLICATION

After mixing, stir lightly with a spatula for a few seconds to release any entrapped air. The grout is then poured immediately into the prepared formwork. When carrying out baseplate grouting, ensure sufficient pressure head is maintained for uninterrupted mortar flow. For formwork repair, the prepared formwork must be firmly in place and kept watertight. When placing grout over a large area, it is important to maintain a continuous flow throughout. Work sequence must be properly organised to ensure an uninterrupted flow. In large areas, SikaGrout® GP AU may be pumped using heavy duty diaphragm pumps. Screw feed and piston pumps may also be used.

 

Specific Areas of Application 

Grouting under baseplate Flowable consistency
Formwork grouting – pouring method Flowable consistency
Formwork grouting – pre-packed method Flowable / Plastic consistency
Grouting anchor bolts Plastic / Stiff consistency
Dry packed / Precast grouting Stiff consistency

Grouting large volumes: For sections thicker than 100 mm, it is necessary to fill ikaGrout® GP AU with graded 10 mm silt free aggregates o minimise temperature rise generated during the during stage. The quantity of aggregates should not exceed 1 part aggregates to 1 part SikaGrout® GP AU by weight. For such mixes, a conventional concrete mixer and pump may be used. To further ensure that air entrapped during mixing is allowed to fully escape, it may be necessary to make breather holes. Use steel rods or chains to assist the flow of grout where necessary. Preliminary trials are recommended.

CURING TREATMENT

When formwork type repair is used, leave the formwork in place for at least 3 days. Upon removal of the formwork, cure the exposed surfaces
immediately with Antisol® curing compound or use other approved curing methods.

Safety Data Sheet (SDS) | Product Data Sheet (PDS)

https://aus.sika.com/en/construction/grouts-landscapinganchoring/cementitious-grouts/sikagrout-gp-au.html

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.

Google Rating
5.0
Based on 79 reviews
×
js_loader