Australia Wide Shipping

Screenshot 2023-01-04 213749Screenshot 2023-01-04 213749

Sika MonoTop 612N – 20kg

$65.00 inc GST

POLYMER MODIFIED HIGH STRENGTH, HIGH BUILD CONCRETE REPAIR MORTAR

Quantity:
SKU: EFA6A0 Categories: ,

Sika® MonoTop-612 N is a cement-based, one component low permeability concrete repair mortar, containing silica fume and polymer, meeting the requirements of Class R4 of EN 1504-3.

Reviews

There are no reviews yet.

Be the first to review “Sika MonoTop 612N – 20kg”

Your email address will not be published. Required fields are marked *

USES

▪ For repairing high strength concrete >45MPa
▪ High Build repairs horizontal, vertical and overhead
▪ For exterior and interior use
▪ New and old concrete repairs
▪ Marine repairs
▪ Trafficable repair applications

 

CHARACTERISTICS AND ADVANTAGES

  • Compatible with Sika® FerroGard® corrosion inhibitors
  • Compatible with Sika® FerroGard® Sacrificial Anode System
  • High build up to 100mm in one application*
  • Low shrinkage
  • High workability
  • Very high resistivity mortar for durable new work concrete repairs
  • AS/AZS 4020:2018 Approved for Potable/ drinking water contact
  • Sulphate resistant in marine

Grey Powder

20 kg bag

MIXING

Sika MonoTop®-612 N can be mixed with a low speed (< 500 rpm) hand drill mixer or for machine application, using a force action mixer 2 to 3 bags or more at once depending the type and size of mixer. In small quantity, Sika MonoTop®-612 N can also be manually mixed. Pour the recommended water in a suitable mixing container. While stirring slowly, add the powder to the water and mix thoroughly at least for 3 minutes to the required consistency.

APPLICATION

Bonding Primer:
On a well prepared and roughened substrate a bonding primer is generally not required for this product. When a bonding primer is required, refer to the System Information above for compatible Sika products and refer to the relevant Product Data Sheet for instructions. All small amount of Sika MonoTop®-612 N can also be mixed slightly wetter than normal and used as a scratch coat to promote adhesion of the repair mortar to the substrate. Any bonding primer shall be applied on a pre-wet substrate in saturated surface dry (SSD) condition and subsequent application of the repair mortar shall be applied wet on wet with the bonding primer.
Reinforcement Corrosion Protection:
Where a reinforcement coating is required the application of a repair mortar shall be applied wet on dry with the reinforcement corrosion protection. Refer to the System Information above for compatible Sika products and refer to the relevant Product Data Sheet for more detailed information about the reinforcement corrosion product. Sika MonoTop®-612 N can be applied either manually using traditional techniques or mechanically using wet spray equipment. Thoroughly pre-wet the prepared substrate a recommended 2 hours before application. Keep the surface wet and maintain in SSD condition. The surface shall appear a dark matt appearance without glistening and surface pores and pits shall not contain water.

When manually applying first make a scratch coat by firmly scrapping the repair mortar over the substrate surface to form a thin layer and fill any pores or pits in the surface. Ensure the whole surface to be repaired is covered by the scratch coat. Build up layers from bottom to top by pressing mortar well into the repair area. The surface can be finished according to the requirements using a float while wet or with a relevant rough-cast tool as soon as the mortar has started to stiffen.

CURING TREATMENT

Protect the fresh mortar immediately from premature drying using an appropriate curing method e.g. curing compound, moist geotextile membrane, polythene sheet etc.

Safety Data Sheet (SDS) | Product Data Sheet (PDS)

https://aus.sika.com/en/construction/concrete-repair-protection/concrete-repair-mortars/cementitious-repairmortars/sika-monotop-612n.html

 

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.

Google Rating
5.0
Based on 79 reviews
×
js_loader